สินค้า / Products


 

Infrared / อินฟราเรด


Infrared Painting Machine



Sipin Power Regulator

UV / ยูวี


UVC Lamp / หลอดยูวีฆ่าเชื้อ


BALLAST FOR UVC LAMP



UVA-UVB / หลอดยูวีเอ-ยูวีบี




สาระน่ารู้

Hot Air Products

   


 Hand-Held Welding Forsthoff


 Hot Air Welding Machine JC Tool


 Welding Rod


High Pressure Blower


 High Frequeny Machine Heagon


 Toshiba Electron Triode Oscillation Tube



 

Thai Inter Lamp Forsthoff

 

Thai Inter lamp ยินดีต้อนรับ เรา จำหน่าย หลอดอินฟราเรด infrared lamp (short wave) และ Infrared Heater, รับสร้างเครื่องอบระบบความร้อนทุกชนิด,                                                                                                                                                                                                                                                          


     W5 Series

 

Product features :


Independent adjustment of Max and BIAS

Down-opened Panel, easy for fuse replacement

VR of Max and SFS are installed in the front panel, easy for adjustment

Multi-LED display panel makes the operating condition clear

The auxiliary powers (AC1, AC2) are independently controlled for all models

Build-in buffering output adjustment (SFS VR), adjusting range 1~22 seconds. (Only for the phase control product) 

Top & bottom shielding covers are designed for safety and fashion out looking, also easy for wiring installation

In case of 0.5 Hz sudden power losses, system output can be switched off immediately. Once the power is restored, the system will buffer the output to prevent the voltage surge for fuse burn-down

Main power is one spec. Design for 200~480VAC

Automatic power frequency detection for 50~60 Hz. No need for selection or switch

Automatic detection and display for power out-of-phase, SCR overheating, and fuse burn-down with one set of alarm dry contact output

In cases of SCR overheating or fuse burn-down, the system output is stopped immediately. Once the malfunction is eliminated and power is restored, the system will buffer the output to prevent the fuse burn-down

4~20mA, 1~5VDC, 2~10VDC, 0~20mA, 0~5 VDC, 0~10VDC, dry contact points, etc. and all control signals are ready to use

Triggering circuit and the main board are designed separately to avoid the main board damage when main circuit malfunctions

Using European detachable control signal connector for easy replacement without re-wiring installation.


Installation and ambient conditions  

When the power regulator is operating, the heat will be generated automatically. Please install the system vertically and leave some empty space on two sides to avoid the temperature inside the regulator rising continuously

There must be some ventilation holes on the control box. Please follow the principle of hard air rising to install the ventilation holes or extra cooling fans

Please avoid installing the regulator in the place with high temperature or poor ventilation. Otherwise, the maximum operating capacity must be set lower than 70% of the nominal capacity

Avoid installing the regulator in the places with heavy water evaporation, acid, alkaline, or corrosive air

Ambient humidity: below 90%RH (no condensation) 

Ambient temperature: -10°C~45°C 

Control and applied loading 

Phase angle control : continuous phase angle control, steady output, current gauge reading remains steady. But, every half wave will produce harmonic wave.

Applicable loading : fixed resistance loading, variable resistance loading, inductive loading, IR light bulb

Zero crossing control : distributed zero crossing control, minimum resolution 1 Hz, no harmonic wave, and current gauge reading oscillates

Applicable loading : fixed resistance loading


Wiring and setup notices 

Single phase Two-wire three-phase Three-wire three-phase NFB → can cut off power to prevent personnel from electric shock during maintenance. MC → can cut off supplied loading power when the power regulator malfunctions or the temperature is higher than the pre-set value. Cutting off the power can avoid the system burn down by overheating and prevent more serious damage. Power regulato → can adjust the output power according to the control signal. (This product is embedded with the high-speed fuse, extra fuse is not necessary.) 


Standard main circuit setup: main power →molded case circuit breaker → contactors → power regulator → loading

The screw must be tightened during the wiring setup to avoid high temperature resulting from bad contact

Once the wiring setup is completed, the front panel and safety cover must be properly installed before the system is powered up to avoid the electric shock or short circuit caused by dropped conductive objects.


NEXT ถัดไป >>>

ข่าวประชาสัมพันธ์

Time & Date

 


Counter

 

 สถิติวันนี้ 30 คน
 สถิติเมื่อวาน 97 คน
 สถิติเดือนนี้
สถิติปีนี้
สถิติทั้งหมด
2085 คน
9363 คน
528977 คน
เริ่มเมื่อ 2012-10-25

 




Contact Our Team

คุณ สิริโชค แซ่ตั้ง 
(คุณหนึ่ง)
Sale Representative
Tel : 086-974-7083


คุณ วีรยุทธ ชัยมุง 
(คุณวี)
Sale Representative
Tel : 086-999-2429





คุณ ธิติพงษ์ สีโลหะ
(คุณแชมป์)
Sale Representative
Tel : 095-748-4173

 

 

Design by Thaiinterlamp 2012